|
 With
over 17 years of experience in trade licensing, Contractor School
Online (CSO) is your primary resource to help you pass your
state contractor license exam! We offer online practice tests,
study materials, books and more.
To become a certified contractor in North Carolina, you must
pass a Business, Law and Management exam.
Depending on the trade you are interested in, you may also be
required to pass a trade exam as well. Please use our Information Request Form to
find out more.
Below is a list of available license classifications in North
Carolina that we can help you to obtain.
NORTH CAROLINA STATE
Contractor School Online will assist you with their professional
consultants and provide study materials, also practice
tests for the Business,
Law and your trade if available. If purchases
are made elsewhere make sure the correct author, title and year
are appropriate for the trade.
Please note: Inventory Pricing - Contractors State Bonding
and Subjects may change without notice.
($85)
Content
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
|
|
($57.98)
-
Business, Law and Management Manual
|
|
($85)
Content
-
Building Contractor Online Practice Test
-
3 Months Access, Available 24/7
|
|
($85)
Content
-
Residential Contractors Online Practice Test
-
3 Months Access, Available 24/7
|
|
($85)
Content
-
Low Voltage Online Practice Test
-
3 Months Access, Available 24/7
|
|
($85)
Content
-
Electrical Online Practice Test
-
3 Months Access, Available 24/7
|
|
($85)
Content
-
Heating and Air Conditioning Online Practice Test
-
3 Months Access, Available 24/7
|
|
($85)
Content
-
Plumbing Online Practice Test
-
3 Months Access, Available 24/7
|
|
($212.98)
-
Business, Law and Management Online Practice Test
-
Building Contractor Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Business, Law and Management Online Practice Test
-
Building Contractor Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Building Contractor Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Business, Law and Management Online Practice Test
-
Residential Contractors Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Business, Law and Management Online Practice Test
-
Residential Contractors Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Residential Contractors Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Business, Law and Management Online Practice Test
-
Electrical Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Business, Law and Management Online Practice Test
-
Electrical Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Electrical Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Low Voltage Online Practice Test
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Low Voltage Online Practice Test
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Low Voltage Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Business, Law and Management Online Practice Test
-
Framing, Millwork, Cabinets, Finish & Rough Carpentry Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($134.98)
-
Framing, Millwork, Cabinets, Finish & Rough Carpentry Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Framing, Millwork, Cabinets, Finish & Rough Carpentry Online Practice Test
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
|
|
($160)
-
Heating and Air Conditioning Online Practice Test
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Heating and Air Conditioning Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Heating and Air Conditioning Online Practice Test
-
Business, Law and Management Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($160)
-
Business, Law and Management Online Practice Test
-
Plumbing Online Practice Test
-
3 Months Access, Available 24/7
|
|
($134.98)
-
Plumbing Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
($212.98)
-
Business, Law and Management Online Practice Test
-
Plumbing Online Practice Test
-
3 Months Access, Available 24/7
-
Business, Law and Management Manual
|
|
Below is a list of available license classifications in North
Carolina
General Contractor
:
Highways Contractor:
Public Utilities Contractor:
- PU-1 Communications
- PU-2 Electrical
- PU-3 Fuel Distribution
- PU-4 Water & Sewer Lines
- PU-5 Water Purification & Sewage Disposal
Specialty Contractor
:
- S-1 Boring & Tunneling
- S-2 Concrete
- S-3 Insulation
- S-4 Interiors
- S-5 Marine
- S-6 Masonry
- S-7 Metal Erection
- S-8 Railroad
- S-9 Roofing
- S-10 Swimming Pools
- S-11 Asbestos
Alarm Systems Contractor
:
- A Alarm Systems License
- L Limited Monitoring & Response
- R Registered Installer
Contractor:
- L Limited - Projects of $25,000 or Less. This may change
- I Intermediate - Projects of $75,000 or Less. This may changes
- U Unlimited
- SP-SFD Special Single Family Dwelling
- SP-EL Special Restricted - Elevators & Escalators
- SP-PH Special Restricted - Plumbing & A/C
- SP-WP Special Restricted - Groundwater Pumps
- SP-ES Special Restricted - Electrical Signs
- SP-LV Special Restricted - Low Voltage
- SP-SP Special Restricted - Swimming Pools
Plumbing Contractor:
- P-I Plumbing Unlimited
- P-II Plumbing Single Family Dwelling
HVAC Contractor
:
- H-1-I Heating Systems Urdimited1
- H-1-II Heating Systems Single Family dwellings
- H-2 Comfort Cooling Systems over 15 tons capacity
- H-3-I Forced Warm Air Heating Systems Unlimited
- H-3-II Forced Warm Air Heating Systems Single
Family Dwelling
GUIDELINES FOR LICENSING-AQUALIFICATION-HOW TO OBTAIN A
LICENSE
STATE EXAMINATION INFORMATION
Failing candidates may not retake an examination until at least
30 days after the failed examination. Failing
candidates are strongly encouraged to evaluate their diagnostic
report and study, particularly the areas of weakness, before
retaking the examination. The following fee table lists the
applicable fee for each examination. The fee is for each examination,
whether you are taking the examination for the first time or
repeating.
SPECIAL EXAMINATION ARRANGEMENTS
All examination centers are equipped to provide access in accordance
with the Americans with Disabilities Act (ADA) of 1990, and
every reasonable accommodation will be made in meeting a candidate’s
needs. Applicants with disabilities or those who would otherwise
have difficulty taking the examination should request for alternative
arrangements with the testing Center. Requests for any special
accommodations should be made in writing, describing the specific
accommodations that will be needed, and must include supporting
documentation on official letterhead from a licensed professional.
REQUIRED IDENTIFICATION AT EXAMINATION SITE
You must provide 2 forms of identification. One must be a VALID
form of government issued identification (driver’s license,
state ID, passport, military ID), which bears your signature
and has your photograph or a complete physical description.
The second ID must have your signature and preprinted
legal name. All identification provided must match the name
on the Eligibility Form.
SCORE REPORTING
In order to pass the examinations, you must receive a score
of at least 70%. Your
score will be given to you immediately following completion
of the examination. The following summary describes the score
reporting process: On
screen –
your score will appear immediately on the computer screen. This
will happen automatically at the end of the time allowed for
the examination; If you pass,
you will immediately receive a successful notification. If you do not pass,
you will receive a diagnostic report indicating your strengths
and weaknesses by examination type with the score report. On paper – an
unofficial score report will be printed at the examination site. This may
change by the Testing Center.
LICENSE EXAMINATION
Your studies will be most effective if you study frequently, for periods of
about 45 to 60 minutes. Concentration
tends to wander when you study for longer periods of time.
EXAMINATION REFERENCE MATERIAL AND CONTENT OUTLINE
If a test question answer could differ because of conflicting
information in test reference sources, a legal requirement such
as code, law, or regulation overrides any other reference. If
two legal requirements appear to conflict, the state-specific
code, law, or regulation overrides the national one. Information
from sources on the test reference list below override information
from other sources or persons.
(S) ASBESTOS
SCOPE OF WORK
This classification covers renovation or demolition activities
involving the repair, maintenance, removal, isolation, encapsulation,
or enclosure of Regulated Asbestos Containing Materials (RACM)
for any commercial, industrial, or institutional building, whether
public or private. It also covers all types of residential building
construction involving RACM during renovation and/or demolition
activities.
Number of Questions: 60
% Required to Pass: 70%
Time Allowed: 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
General Asbestos 18
Respirators 10
Mini Enclosures and Glove Bag 5
Methods and Means 24
Laws and Regulations 2
Liens 1
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Federal Asbestos Regulations
Asbestos Operations and Maintenance
The following reference materials are not allowed in the examination
center:
Asbestos Abatement & Management in Buildings
Contractor’s Business, Law and Management
Laws and Regulations Applicable to Contracting
(S) BORING AND TUNNELING
SCOPE OF WORK
This classification covers the construction of underground or
underwater passageways by digging or boring through and under
the earth’s surface, including the bracing and compacting of
such passageways to make them safe for the purpose intended
and includes preparation of the ground surfaces at points of
ingress and egress.
Number of Questions - 60
% Required to Pass – 70%
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Boring and Tunneling 22
Sitework 6
Concrete 10
Concrete Reinforcement 5
Hoisting and Rigging 5
Safety 5
One Call 2
Erosion and sedimentation control 2
Liens 1
Laws and Regulations 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Rigging: For Construction and Industrial Operations
The following reference materials are not allowed in the examination
center
NC Administrative Code
NC General Statutes
NC Excavation
Contractor’s Business, Law and Management
Pipe and Excavation Contracting
Laws and Regulations Applicable to Contracting
Jacked Tunnel Design and Construction
Standard Construction for Micro-tunneling
Code of Practice for Tunnels
Cost Estimating for Underground Transit
Control of Concrete Mixtures
Training and Certification of Field Personnel for Un-bonded
Post-Tensioning
Reinforcing Bars
BUILDING CONTRACTOR
SCOPE OF WORK
This classification covers all types of building construction
activity including but not limited to: commercial, industrial,
institutional, and all types of residential building construction;
covers parking decks; all site work, grading and paving of parking
lots, driveways, sidewalks, curbs and gutters which are ancillary
to the aforementioned types of construction; and covers the
work done under the specialty classifications of (S) Concrete
Construction, (S) Insulation, (S) Interior Construction, (S)
Masonry Construction, (S) Roofing, (S) Metal Erection, and (S)
Swimming Pools.
Number of Questions - 90
% Required to Pass - 70
Time Allowed – 180 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Site work 6
Concrete 15
Masonry 6
Metals 15
Carpentry 7
Roofing 6
Associated Trades 3
Business, Law and Management 7
Safety 4
Estimating, Plan Reading and General BuildingmCode Requirements
14
One Call 2
Erosion and Sedimentation Control 2
Licensing 2
Liens 1
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Contractor’s Business, Law and Management
State Building Code
ACI 530-05 or 08 Building Code Requirements for Masonry Structures
ACI 318-05 or 08 Building Code Requirements for Structural Concrete
and Commentary
State Building Code
The following reference materials are not allowed in the examination
center
Erection of Steel Joists and Joist Girders
Carpentry and Building Construction
Control of Concrete Mixtures
Pipe and Excavation
Roofing Construction and Estimating
Training and Certification of Field Personnel for Un-bonded
Post-Tensioning
Masonry - Brick, Block and Stone
NC One-Call Excavation Manual
Administrative Code, Title 15A
General Statutes Chapter 113A
Laws and Regulations Applicable to Contracting
SDI: Of Construction with Steel Deck
(PU) COMMUNICATIONS
SCOPE OF WORK
This classification covers the installation of all types of
pole lines, and aerial and underground distribution cable for
telephone systems; aerial and underground distribution cable
for Cable TV and Master Antenna TV Systems capable of transmitting
R.F. signals; underground conduit and communication cable including
fiber optic cable; and microwave systems and towers, including
foundations and excavations where required, when the microwave
systems are being used for the purpose of transmitting R.F signals;
and installation of PCS or cellular telephone towers and sites.
Number of Questions - 45
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
MATV and Cable TV systems 7
Antennas 7
Foundations and Sitework 8
Steel Erection 8
Safety 6
Erosion and Sedimentation Control 2
One Call 2
Underground Cabling 2
Liens 1
Licensing and Regulations 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
The following reference materials are not allowed in the examination
center:
Contractor’s Business, Law and Management
State Antenna Toolkit Administrative Code
General Statutes Chapter 113A
Control of Concrete Mixtures
Welding
NC One-Call Excavation
Pipe and Excavation
Data, Voice, and Video Cabing
Laws and Regulations
(S) CONCRETE CONSTRUCTION
SCOPE OF WORK
This classification covers the construction and installation
of foundations, pre-cast silos and other concrete tanks or receptacles,
prestressed components, and gunite applications, but excludes
bridges, streets, sidewalks, curbs, gutters, driveways, parking
lots and highways.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Safety 5
Concrete Earthwork 3
Concrete 11
Concrete Reinforcement 9
Concrete Formwork 10
Concrete Cutting 3
Pre-cast Pre-stressed Concrete 4
Laws and Regulations 2
Liens 1
General Building Code Requirements 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
State Building Code
ACI 318-05 or 08 Building Code
Administrative Code and Policies
The following reference materials are not allowed in the examination
center
Formwork for Concrete
Control of Concrete Mixtures
Sawcutting Joints in Concrete,
Sawcutting Concrete Flatwork
Taking the Tedium Out of Cutting
Cutting Concrete
Standards and Erection of Pre-Cast Concrete Products
Contractor’s Business, Law and Management
Laws and Regulations Applicable
Reinforcing Bars
(PU) ELECTRICAL -- AHEAD OF POINT OF DELIVERY
SCOPE OF WORK
This classification covers the construction, installation, alteration,
maintenance or repair of an electrical wiring system, including
sub-stations or components thereof, which is or is intended
to be owned, operated and maintained by an electric power supplier
such as a public or private utility, a utility cooperative,
or any other properly franchised electric power supplier, for
the purpose of furnishing electrical services to one or more
customers.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Transformers 6
Electrical Knowledge 6
Conductors 7
Overhead Lines 5
Underground Lines 3
Equipment and Safety 10
Grounding Methods 3
Service Drops and Laterals 1
Poles and Structures 3
Electric Supply Stations 3
Laws and Regulations 2
Liens 1
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
National Electrical Safety Code
Lineman's and Cableman's Book
National Electrical Code
Safety and Health Standards
The following reference materials are not
allowed in the
examination center
Contractor’s Business, Law and Management
American Electricians
Laws and Regulations Applicable to Contracting
(PU) FUEL DISTRIBUTION
SCOPE OF WORK
This classification covers the construction, installation, alteration,
maintenance or repair of systems for distribution of petroleum
fuels, petroleum distillates, natural gas, chemicals and slurries
through pipeline from one station to another. Includes all excavating,
trenching and backfilling in connection therewith. Covers the
installation, replacement and removal of above ground and below
ground fuel storage tanks.
Number of Questions - 60
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Excavation 10
Tank and Vaults 12
Piping. Pumps, and Controls 11
Troubleshooting and Maintenance 2
Safety and Fire Prevention 8
Leak Detection and Monitoring Systems 3
Erosion and Sedimentation Control 3
One Call 2
Laws and Regulations 2
Liens 1
Gas 6
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Flammable and Combustible Liquids Code
Motor Fuel Dispensing Facilities and Repair Garages
Installation of Underground Liquid Storage Systems (RP100)
Installation of Aboveground Storage Systems for Motor Vehicle
Refueling (RP200
Testing Electrical Continuity of Fuel-Dispensing Hanging Hardware
(RP400
Code for Pressure Piping - B31.8 - Gas Transmission and Distribution
Piping Systems
The following reference materials are not
allowed in the
examination center
Administrative Code, Title 15A
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
NC One-Call Excavation
Contractor’s Business, Law and Management
Pipe and Excavation
Laws and Regulations Applicable to Contracting
(H) GRADING AND EXCAVATING
SCOPE OF WORK
This classification covers the digging, moving and placing of
materials forming the surface of the earth (excluding air and
water) in such a manner that the cut, fill, excavation, grade,
trench, backfill, or any similar operation can be executed with
the use of hand and power tools and machines commonly used for
these types of digging, moving and material placing. Covers
work on earthen dams and the use of explosives used in connection
with all or any part of the activities described in this Sub-paragraph.
Also includes clearing and grubbing, and erosion control activities.
Number of Questions - 45
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
General Knowledge and Regulations 9
Excavating and Grading 18
Safety - Code of Federal Regulations 6
Lien Law 1
Licensing and Regulations 2
One Call 3
Erosion and Sedimentation Control 6
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. Code
questions, the examinations will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Standard Specifications for Roads and Structures
The following reference materials are not allowed in the examination
center
Administrative Code, Title 15A
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
NC One-Call Excavation
Contractor’s Business, Law and Management
Pipe and Excavation
Laws and Regulations Applicable to Contracting
HIGHWAY CONTRACTOR
SCOPE OF WORK
This classification covers all types of highway construction
activity including but not limited to: grading, paving of all
types, installation of exterior artificial athletic surfaces,
relocation of public and private utility lines ancillary to
the principal project, bridge construction and repair, parking
decks, sidewalks, curbs, gutters and storm drainage. Includes
installation and erection of guard rails, fencing, signage and
ancillary highway hardware; covers paving and grading of airport
and airfield runways, taxiways, and aprons, including the installation
of signage, runway lighting and marking; and covers work done
under the specialty classifications of (S) Boring and Tunneling,
(S) Concrete Construction, (S) Marine Construction and (S) Railroad
Construction.
Number of Questions - 90
% Required to Pass - 70
Time Allowed – 240 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Paving-Asphalt 14
Piles 5
Excavation and Grading 9
Concrete Paving 3
Safety 5
One-Call 3
Traffic Control 2
Concrete 6
Metals including Concrete Reinforcement 5
Erosion and Sedimentation Control 6
Tunneling 8
Railroad Construction 8
Marine Construction 6
Licensing 2
Liens 1
Business, Law and Management 7
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Contractor’s Business, Law and Management
Standard Specifications for Roads and Structures
Safety and Health Standards
Construction Planning, Equipment
CAMA for Development of Coastal
The following reference materials are not
allowed in the
examination center
Administrative Code, Title 15A, Chapter 4 Sedimentation Control
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
NC One-Call Center Excavation
Pipe and Excavation
Control of Concrete Mixtures
Hot-Mix Asphalt Paving
Laws and Regulations Applicable to Contracting
Reinforcing Bars
Training and Certification of Field Personnel for Un-bonded
Post-Tensioning
Jacked Tunnel Design and Construction
Guide to Railway Engineering
(S) INSULATION
SCOPE OF WORK
This classification covers the installation, alteration, or
repair of materials classified as insulating media used for
the non-mechanical control of temperatures in the construction
of residential and commercial buildings. Does not include the
insulation of mechanical equipment and ancillary lines and piping.
Number of Questions - 40
% Required to Pass - 70
Time Allowed – 90 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
General Knowledge and Principles 10
Liens 1
Insulation types and properties 15
Radiant and reflective barriers, vapor retarders 7
Safety 5
Laws and regulations 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Energy Code, 2002, (you may use either the 2002 or the 2006
North Carolina Energy Code from 9/1/06 thru 12/31/06. As
of 1/1/07, only the 2006 code can be used.)
The following reference materials are not
allowed in the
examination center
Contractor’s Business, Law and Management
Insulation
Laws and Regulations Applicable to Contracting
(S) INTERIOR CONSTRUCTION
SCOPE OF WORK
This classification covers installation of acoustical ceiling
systems and panels; drywall portions (load bearing and non-bearing);
lathing and plastering; flooring and finishing; interior recreational
surfaces; window and door installation; and installation of
fixtures, cabinets, and millwork. Includes the removal of asbestos
and replacement with non-toxic substances.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Asbestos Removal 6
Windows and Doors 3
Framing - Wood and Metal 7
Finish Carpentry and Millwork 7
Drywall and Plaster 15
Flooring and Finishes 5
Acoustical Ceilings 2
Laws and Regulations 2
Liens 1
Permits and Inspections 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
State Building Code
State Building Code: Administrative Code and Policies
The following reference materials are not
allowed in the
examination center
Gypsum Construction
Guide to Floors
Contractor’s Business, Law and Management
Finish Carpenter's
Asbestos Operations and Maintenance
Laws and Regulations Applicable to Contracting
Plastering Skills
Illustrated to Furniture and Cabinet Construction
(S) MARINE CONSTRUCTION
SCOPE OF WORK
This classification covers all marine construction and repair
activities and all types of marine construction in deep-water
installations and in harbors, inlets, sounds, bays, and channels;
covers dredging, construction and installation of pilings, piers,
decks, slips, docks, and bulkheads. Does not include structures
required on docks, slips, and piers.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
CAMA Regulated Areas 7
Small Docks 7
Pile Driving 12
Concrete 7
Concrete Reinforcement 7
Safety 5
Laws and Regulations 2
Liens 1
Erosion and Sedimentation Control 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
CAMA for Development
Construction Planning, Equipment, and Methods
The following reference materials are not allowed in the examination
center
Administrative Code, Title 15A, Chapter 4 Sedimentation Control
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Concrete Mixtures
Designing, Building, Maintaining
Contractor’s Business, Law and Management
Reinforcing Bars
Laws and Regulations Applicable to Contracting
(S) MASONRY CONSTRUCTION
SCOPE OF WORK
This classification covers the installation, with or without
the use of mortar or adhesives, of the following: brick, concrete
block, gypsum partition tile, pumice block or other lightweight
and facsimile units and products common to the masonry industry;
fire clay products and refractory construction; rough cut and
dressed stone, marble panels, and slate units, and installation
of structural glazed tile or block, glass brick or block, and
solar screen tile or block.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Safety 5
Concrete Block 16
Brick 12
Specialty Masonry 4
Mortar and Grout 8
Laws and Regulations 2
Liens 1
General Building Code Requirements 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
State Building Code
ACI 530-05 or 08 Building Code for Masonry Structures
Administrative Code and Policies
The following reference materials are not
allowed in the
examination center
Masonry - Brick, Block and Stone
Contractor’s Business, Law and Management
Laws and Regulations Applicable to Contracting
(S) METAL ERECTION
SCOPE OF WORK
This classification covers the field fabrication, erection,
repair, and alteration of architectural and structural shapes,
plates, tubing, pipes and bars, not limited to steel or aluminum,
that are or may be used as structural members for buildings,
equipment, and structure; and covers the layout, assembly, and
erection by welding, bolting or riveting such metal products
as, but not limited to, curtain walls, tanks of all types, hoppers,
structural members for buildings, towers, stairs, conveyor frames,
cranes and crane runways, canopies, carports, guard rails, signs,
steel scaffolding as a permanent structure, rigging, flagpoles,
fences, steel and aluminum siding, bleachers, fire escapes,
and seating for stadiums, arenas, and auditoriums.
Number of Questions - 65
% Required to Pass - 70
Time Allowed – 150 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Metal Roofing and Siding 5
Reinforcing Steel 8
Safety - OSHA Subpart R 7
Safety - General 6
Steel Decks 7
Steel Joists and Girders 15
Welding 6
Bolting 3
Laws and Regulations 2
Liens 1
Metal Fencing 5
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Structural Joints Using ASTM A325 or A490 Bolts
The following reference materials are not allowed in the examination
center
Sheet Roofing and Cladding
Reinforcing Bars
Erection of Steel Joists and Joist Girders
Laws and Regulations Applicable to Contracting
SDI: Construction with Steel Deck
Contractor’s Business, Law and Management
Welding
Fences and Retaining Walls
(PU) PUBLIC UTILITIES CONTRACTOR
SCOPE OF WORK
This classification includes those whose operations are the
performance of construction work on the following Sub-classifications
of facilities: a). Water and sewer mains and water service lines
and house and building sewer lines as defined in the North Carolina
State Building Code, and water storage tanks, lift stations,
pumping stations, and appurtenances to water storage tanks,
lift stations and pumping stations; b). Water wastewater-treatment
facilities, and appurtenances thereto; c). Electrical power
transmission facilities, and primary and secondary distribution
facilities ahead of the point of delivery of electric service
to the customer; d). Public communication distribution facilities;
e). Natural gas and other petroleum products distribution facilities.
Within appropriate sub-classification, a public utilities contractor
license covers work done under the specialty classifications
of S(Boring and Tunneling), (PU) Communications, (PU) Fuel Distribution,
(PU) Electrical-Ahead of Point of Delivery, and (S) Swimming
Pools.
Number of Questions - 100
% Required to Pass - 70
Time Allowed – 240 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Excavation and Grading 6
Electrical Power Distribution 15
Fuel Distribution 12
Swimming Pools 4
Concrete and Concrete Reinforcement 12
Shotcrete and Gunite 4
Water and Sewer Piping 12
Communication Systems 3
Boring and Tunneling 4
Erosion and Sedimentation Control 2
Safety 8
Liens 1
Licensing 2
Business, Law and Management 7
One Call 2
Welding 6
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Contractor’s Business, Law and Management
Safety and Health Standards
Administrative Code Title 15A Sub-chapter 18C: Water Supplies
Public Swimming Pools
Installation of Above-ground Storage Systems for Motor Vehicle
Refueling (RP200
Testing Electrical Continuity of Fuel-Dispensing
Hanging Hardware
Code for Pressure Piping-B31, 8-Gas Transmission and Distribution
Piping Systems
National Electrical Safety Code
The Lineman's and Cableman's Book
Installation for Ductile Iron Pipe
Concrete Pipe and Box Culvert Installation
The following reference materials are not allowed in the examination
center
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
NC One-Call Excavation
Pipe and Excavation
Laws and Regulations Applicable to Contracting
Jacked Tunnel Design and Construction
Standards for the Erection of Pre-Cast Concrete Products
Welding
Control of Concrete Mixtures
Shotcrete
(S) RAILROAD CONSTRUCTION
SCOPE OF WORK
This classification covers the building, construction, and repair
of railroad lines, including: clearing and filling rights-of-way;
shaping, compacting, setting and stabilizing road beds; setting
ties, tie plate rails, rail connectors, frogs, switch plates,
switches, signal markers, retaining walls, dikes, fences and
gates; and construction and repair of tool sheds and platforms.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Erosion and Sedimentation Control 2
Track Construction 16
Concrete Railway Structures 15
Safety 7
Sitework 5
One Call 2
Laws and Regulations 2
Liens 1
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Track Safety Standards; Part 214 - Railroad Workplace Safety;
and Part 236 - Rules, Standards, and Instructions Governing
the Installation, Inspection, Maintenance, and Repair of Signal
and Train Control Systems, Devices, and Appliances
The following reference materials are not
allowed in the
examination center
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Contractor’s Business, Law and Management
NC One-Call Excavation
Railway Engineering
Concrete Railway Structures, American Railway Engineering and
Maintenance of Way Association (AREMA)
Pipe and Excavation
Laws and Regulations Applicable to Contracting
RESIDENTIAL CONTRACTOR
SCOPE OF WORK
This classification covers all types of construction activity
pertaining to the construction of residential units that are
required to conform to the residential building code adopted
by the Building Code Council pursuant to G.S. 143-138. It covers
all site work, driveways, and sidewalks ancillary to the aforementioned
construction; and covers the work done as part of such residential
units under the specialty classifications of (S) Insulation,
(S) Masonry Construction, (S) Roofing, and (S) Swimming Pools.
Number of Questions - 90
% Required to Pass - 70
Time Allowed – 210 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Site work, Footings and Foundations 12
Concrete and Concrete Reinforcement 10
Masonry 7
Carpentry 11
Associated Construction trades, including Energy Conservation
and Drywall 8
Roofing 6
Estimating, Plan Reading and General Residential Code Requirements
16
OSHA Safety 4
Licensing and Business, Law and Management 10
Special Construction Zones (wind and coastal) and Erosion and
Sedimentation Control 6
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Contractor’s Business, Law and Management
State Residential (One- and Two- Family Dwelling)
State Building Code: Administrative Code and Policies
The following reference materials are not
allowed in the
examination center
Carpentry and Building Construction
Roofing Construction and Estimating
Masonry - Brick, Block and Stone
Pipe and Excavation
Quality Concrete Construction
Handling, Installing, Restraining, and Bracing of Metal Plate
Connected Wood Trusses
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Laws and Regulations Applicable to Contracting
(S) ROOFING
SCOPE OF WORK
This classification covers the installation and repair of roofs
and decks on residential, commercial, industrial, and institutional
structures requiring materials that form a watertight and weather-resistant
surface. The term “material” shall be defined for purposes of
this Subparagraph to include, among other things, cedar, cement,
asbestos, clay tile, and composition shingles, all types of
metal coverings, wood shakes, single ply, and built-up roofing,
protective and reflective roof and deck coatings, sheet metal
valleys, flashings, gravel stops, gutters and downspouts, and
bituminous waterproofing.
Number of Questions - 60
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Safety 5
Roofing - Substrate 6
Roofing - Steep 18
Roofing Repairs 4
Roofing - Elastomeric 6
Roofing - Built-up Bituminous 6
Business, Law and Management 7
Sheet Metal and Flashing 3
Licensing 2
Liens 1
General Building Code Requirements 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
State Building Code
Contractor’s Business, Law and Management
Administrative Code and Policies
Roofing: Steep Slope Roof Systems
Roofing: Metal Panel and SPF Roof Systems
Roofing: Membrane Roofing Systems
The following reference materials are not
allowed in the
examination center
Roofing Construction and Estimating
Laws and Regulations Applicable to Contracting
(S) SWIMMING POOLS
SCOPE OF WORK
This classification covers the construction, service, and repair
of all swimming pools. Includes: (i) Excavation and grading;
(ii) Construction of concrete, gunite, and plastic-type pools,
pool decks, and walkways, tiling and coping; and (iii) Installation
of all equipment including pumps, filters, and chemical feeders.
Does not include direct connections to a sanitary sewer system
or to potable water lines, nor the grounding and bonding of
any metal surfaces or the making of any electrical connections.
Number of Questions - 60
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Filtration/Circulation Systems 15
Maintenance and Operation 10
Accessories and Associated Trades 8
Concrete, Shotcrete and Gunite 10
Design 10
Laws and Regulations 2
Liens 1
One Call 2
Erosion and Sedimentation Control 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Public Swimming Pools
Equipment for Swimming Pools, Spas, Hot Tubs, and Other Recreational
Water Facilities
The following reference materials are not
allowed in the
examination center
NC One-Call Excavation
Shotcrete
Quality Concrete Construction
Pool Maintenance: Spas, Pools, Hot Tubs, Rockscapes and Other
Water Features
Standard for Public Swimming Pools
National Standard for Residential Inground Swimming Pools
Standard for Public Spas
Standard for Permanently Installed Residential Spas
Certified Pool-Spa Operators Book
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Contractor’s Business, Law and Management
Laws and Regulations Applicable to Contracting
(PU) WATER LINES AND SEWER LINES
SCOPE OF WORK
This classification covers construction work on water and sewer
mains, water service lines, and house and building sewer lines
as defined in the North Carolina State Building Code, and covers
water storage tanks, lift stations, pumping stations, and appurtenances
to water storage tanks, lift stations, and pumping stations,
this includes pavement patching, backfill, and erosion control
as part of such construction.
Number of Questions - 45
% Required to Pass -70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Safety 6
General Knowledge 3
Underground Utilities-Concrete Pipe Installation 10
Underground Utilities-Ductile Pipe Installation 10
Excavating and Grading 9
Liens 1
Erosion and Sedimentation Control 2
NC One-Call 2
Laws and Regulations 2
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Guide for Ductile Iron Pipe
Concrete Pipe & Box Culvert
The following reference materials are not
allowed in the
examination center
NC One-Call Excavation
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Contractor’s Business, Law and Management
Pipe and Excavation
Laws and Regulations Applicable to Contracting
(PU) WATER PURIFICATION AND SEWAGE DISPOSAL
SCOPE OF WORK
This classification covers the performance of construction work
on septic systems, water and wastewater treatment facilities
and covers all site work, grading, and paving of parking lots,
driveways, sidewalks, and curbs and gutters that are ancillary
to such construction of water and wastewater treatment facilities.
Covers the work done under the specialty classifications of
(S) Concrete Construction, (S) Insulation, (S) Interior Construction,
(S) Masonry Construction, (S) Roofing, and (S) Metal Erection
as part of such work on water and wastewater treatment facilities.
Number of Questions - 50
% Required to Pass - 70
Time Allowed – 120 minutes
CONTENT OUTLINE
Subject Area
Number
of Items
Safety 6
Shotcrete 5
Concrete 8
Concrete Reinforcement 7
Excavation and Grading 7
Water Regulations 2
Laws and Regulations 4
Liens 1
One Call 2
Erosion and Sedimentation Control 2
Formwork 6
REFERENCE LIST
The reference material listed below was used to prepare the
questions for this examination. The examination may also contain
questions based on trade knowledge or general industry practices. Except for Code books,
you can base your answers on later editions of references as
they become available. For Code questions, the examinations
will be based only on the edition
of the Code book that is listed.
This examination is OPEN
BOOK.
The following reference materials are allowed in the examination
center
Safety and Health Standards
Administrative Code Title 15A Sub-Chapter 18C: Water Supplies
The following reference materials are not
allowed in the
examination center
NC One-Call Excavation
Contractor’s Business, Law and Management
Laws and Regulations Applicable to Contracting
Administrative Code, Title 15A, Chapter 4 Sedimentation Control,
as amended July 1, 2000
General Statutes Chapter 113A, Article 4 Sedimentation Pollution
Control Act of 1973
Pipe and Excavation
Control of Concrete Mixtures
Shotcrete
Reinforcing Bars
Formwork for Concrete
Contractor School Online will assist you with their professional
consultants and provide study materials, also practice
tests for the Business,
Law and your trade if available. If purchases
are made elsewhere make sure the correct author, title and year
are appropriate for the trade.
Please note: Inventory Pricing - Contractors State Bonding
and Subjects may change without notice.
|
